Stamped and bent parts for precise metal processing and complex assemblies
Stamped and bent parts from OEB are created exactly according to drawings or samples – from flat steel, slit strip or sheet metal. We stamp, bend, edge, laser and rivet all common metal materials and process them into ready-to-use assemblies. Whether small series or large series: With modern forming technology and an experienced team, we deliver your stamped and bent parts with a precise fit, economically and ready for assembly.
Your Benefits at a Glance
Production according to drawing or sample
Complex assemblies can also be realized
All processing from a single source
Economical from medium quantities
Exact implementation of customer-specific geometries
Target groups & areas of application
Stamped and bent parts are used wherever exact geometries, cost-efficient production and a high variety of materials are required. Whether in load-bearing components or precision mechanical assemblies – OEB delivers precise and assembly-ready metal parts.
Versatile – the right connection solution for every industry
- Automotive industry
- Mechanical and plant engineering
- Electrical engineering
- Telecommunications
- Medical technology
- Defense technology
- Agriculture / Farming
Overview of other connection solutions
In addition to stamped and bent parts, OEB also supplies wire bent parts, turned and milled parts or assemblies from combined manufacturing processes – precisely tailored to your requirements.
Stamped and bent parts individually tailored to your requirements
Do you need a sheet metal part with a complex geometry, tight tolerances or as a pre-assembled assembly? OEB manufactures your stamped and bent parts exactly according to drawings or samples – including all forming, joining and post-processing steps. From individual parts to series production, you get everything from a single source – precisely fitting, economical and easy to assemble. Typical individualizations:
- Material selection: steel, stainless steel, aluminum, brass, copper
- Combination of stamping, bending, edging, deep drawing, riveting
- Dimensions and contours exactly as specified
- End processing, cutouts, holes or embossing
- Surface finishing, heat treatment and complete assembly
Materials & Standards
We process all common materials – from stainless steel A2/A4 to aluminum and brass to special case-hardening and tempered steels. Our production always takes place in accordance with standards or exactly according to your drawing – including tested documentation and complete traceability.ren requirements for weight, corrosion resistance or electrical conductivity. Our production is based on all relevant standards – for precisely fitting special screws with maximum reliability.
Steel
Tool and free-cutting steels
Stainless steels
Brass
Aluminum
Other non-ferrous metals
Specifications
OEB manufactures stamped and bent parts from steel, stainless steel, aluminum, brass and other non-ferrous metals – depending on requirements from slit strip, flat steel or sheet metal. In addition to stamping and bending, we integrate other processes such as edging, deep drawing, embossing or riveting. Surface treatments such as galvanizing, dacromet or delta-tone as well as coatings and thread locking devices are just as possible as heat treatments. Complete sampling according to VDA or PPAP is also part of the scope of delivery on request.
Additional processing
End machining:
- Shaft slots
- Contact dome
- Contact tip
- Pin
- Other as required
- Machining post-processing
Surfaces
- All common
- Galvanized (CrVI-free, RoHS compliant)
- nickel-plated
- chromated
- Delta Tone and Seal
- Dacromet
- Geomet etc. according to the specifications of the automotive and electrical industry (VDA standard)
Coatings
- Thread locks
- Thread sealants (e.g. Tuflok, ScotchGrip, Precote, Loctite, wax coatings)
Heat treatment
- All common
- Tempering
- Carbonitriding
- Tempering
- Annealing
- Case hardening
- More upon request
Documentation
All possible documentation for initial sampling is available:
- Standard EMPB as cover sheet sample
- VDA Volume 2 Level 0-3
- PPAP Level 1-3
Product types
| Product |
|---|
| Stamped and bent parts |
| Complex assemblies made of metal materials |
Exemplary applications of stamped and bent parts
OEB stamped and bent parts fulfill a variety of functions – from support and guide elements to load-bearing structural parts in complex assemblies. They can be deformed, screwed, riveted or welded.
What our customers say
Our assembly would not have been possible without the precise stamped and bent parts from OEB. We were particularly impressed by the consistent quality and adherence to delivery dates.
Contact us today
Whether individual part or multi-part assembly – we advise you personally, solution-oriented and with technical know-how. Our team accompanies you from the drawing to the finished assembly – including material selection, processing and surface finishing. Contact us – we will find the optimal solution for your stamped and bent parts.
